Introduction -
Texture/ Structure finish paint is a combination of different resins, suitable anticorrosive pigments & special additives. This system gives excellent non-yellowing property, very tough film with required flexibility. Paint film cures at slightly higher temperature than normal Stoving system. In a single application texture or structure finish will be obtained with film build. This finish gives very nice aesthetic appeal.
RANGE OF APPLICATION
This paint is suitable for Exterior as well as Interior application mainly in control Panels, Machinery parts, Toys, Automobile parts, Computer Tables, Steel Furniture.
KEY PROPERTIES
a. Over-coating or stipple finish is not required to get achieve texture/structure finish.
b. Excellent mar resistance
c. Hardness, scratch hardness is equivalent to powder coating.
d. Excellent abrasion resistance.
e. Good water & weather resistance.
f. Unaffected by spillage of Solvents, Oils, & detergents.
g. Hi-Build film formation ( Higher DFT )
| Type | Specially designed resin systems with suitable pigment & solvent combinations |
| Drying | Stoving at 130 to 140° C for 30 Min with 10- 15 Min. Air flash off |
| Packing Viscosity | 70 to 90 sec at 30° C by Ford cup No B4 |
| Fineness of Grinding | 7+ H.G |
| Covering Capacity | 6 to 7.5 Sq. Mtr /Ltr at DFT 50-60 Microns Required coats 2 wet on wet |
| Thinner | Thinner is not recommended |
| Cleaner | Thinner ST-102/ EP-102/ NC-102 |
| Recommended Application Viscosity | Supplied Viscosity 70 to 90 Sec by FC Cup No B4 |
| Flash Point | Below 22° C |
| Recommended DFT | Minimum 50 Microns Maximum 75 Microns. |
| Finish | Texture/ Structure & Semi-glossy |
| Shades | As per customers requirement |
| Flexibility & Mechanical Propertie | Excellent |
| Weather & Corrosion Resistance | Excellent (5% NaCl solution) Minimum 96-100 Hours |
| Recommended Primer Coat MS | Fast primer Surfacer or Stoving primer surfacer S. S. & Aluminum Etch Primer |
| Shelf Life | Minimum 8 months (Viscosity rise will not be more than 60%) |
| (In packed & at normal temp may cause defect in finish coat.) |
Application:
Before application of Texture/Structure finish coat do all necessary pretreatment on the Job. For M. S. surface, remove grease, oil & loose scale & other contamination by using degreasing Agent. Blast cleans the surface before primer coat recommended, do phosphating & passivation. See that primer coat is fully cured before application of structure coat. Do not add any thinner in paint, Apply Tuff Coat Structure finish at 40-60 psi on primer coat with minimum DFT 50 icrons.1st coat should be horizontal, then give 5-10 flash off, another coat should be vertical (Wet on wet two coats)
While application see that the primer coat will be covered properly. Give 10-15 air flash off & keep the object into oven at 130-140° C for 30 while application structure/
texture pattern automatically appears on the object. After Stoving film shows excellent tough & textured finish. After use of paint, close the container immediately to avoid solvent losses & thickening of paint. Thickening of paint may disturb the pattern of paint film. Do not apply the paint in very high humid condition, during raining or mist & fog or at very low temperature.
Tuff Coat Polymers Pvt. Ltd.
Sr. No. 143/1, Umed Building, B - Wing, Flat No. B - 102, Lagad Mala, Sinhagad Road, Dhayari, Taluka Haveli, Behind Surya Electronic, Pune – 411041
Sales: +91 96045 12297 / +91 81498 31297
Purchase: +91 98814 08404
Accounts: +91 99212 40404
